Hendrix Machinery, Inc.
(912) 964-7790
1725 Old Dean Forest Road
Pooler, GA 31322


2018 LAND PRIDE RC2515

2018 LAND PRIDE RC2515 at www.hendrixmachinery.com2018 LAND PRIDE RC2515 at www.hendrixmachinery.com
2018 LAND PRIDE RC2515 at www.hendrixmachinery.com2018 LAND PRIDE RC2515 at www.hendrixmachinery.com
2018 LAND PRIDE RC2515 at www.hendrixmachinery.com2018 LAND PRIDE RC2515 at www.hendrixmachinery.com

For Sale Price:Call


The new RC2515, a 15' version of our popular 12' medium-duty Rotary Cutter, is an economical solution for general grass cutting needs. The Land Pride gearboxes feature a 1-5/8" output shaft and stout lower bearings. The gearboxes are driven by a constant velocity Cat. 4 main driveline and Cat. 3 connecting drivelines with slip-clutch protection on all three. The ride is cushioned by a deck-mounted spring and can be enhanced with optional 29" used aircraft tires – either 4 or 6 per cutter.

Surpassed rugged industry standards
All Land Pride Cutters have been designed and tested and meet rigorous voluntary testing procedures.

Factory assembled
Saves customer set-up time and money.

5 Year gearbox warranty
Shows confidence in gearbox integrity.

160 hp Divider gearbox and 75 hp wing gearboxes
A rugged heavy built gearboxes capable of handling heavy cutting applications.

Gearbox seal protection
Gearbox bottom seal protection for longer bearing life.

Input driveline: Cat. 4 CV
Driveline is matched just right for capacity of tractor. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline.

Easy greasable drivelines
Drivelines have access holes for greasing the U-joints and to grease the inner profiles.

2 Plate slip-clutch
Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline when impacts are encountered.

15,000 fpm high blade tip speed
Allows clean cutting of material and even distribution.

6" Blade overlap
Eliminates skipping during turns.

11 1/4" Deck height
Handles heavy cutting, which reduces balling-up of cut material under the deck.

3/16" Gauge Stump jumper backed with a 1" thick mounting bar
Allows cutter to slide over obstructions protecting gearbox output shaft & bottom seal.

10 Gauge smooth deck top
Reduces accumulation of debris and is easier and faster to clean.

1/4" Plate side skirt
Reduces debris piercing possibilities.

Low hitch weight
Less drawbar wear. Less ballast required. Works well with lighter tractors.

Dual remote hydraulics
Easy to operate. Fits most tractors, only two duplex outlets required to lift wings and change cutting height separately.

Hinged wing sections
Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches and hollows can cause uneven cutting. Wings will hinge 20o down.

7/8" Solid hinge rods
Gives great strength to the cutter from front to rear, and in the hinge area itself.

Wing transport locks
Holds transport wings in the folded-up position in case of hydraulic pressure loss.

Enclosed front to rear dual leveling rods
Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain. Many competitors only use one leveling rod.

5-Bolt hubs
5-Bolt hubs makes the wheel assembly more durable and longer lasting.

Drain holes in wheel rims
Allows water to drain from wheels mounted on folded-up wings. Helps prevent paint deterioration and rusting to the wheel rims.

Spring-cushioned lift cylinder
Cushions loads on drawbar.

Replaceable wheel spindles
Wheel spindles can be replaced when damaged without replacing the entire axle. Simply remove two bolts to replace damaged spindle.

7/8" Leveling rods
Large diameter leveling rods provide superior supporting strength over rough terrain.

Airplane tires
Gives better cushion while transporting and provides flotation in soft ground.


Power take-off Horsepower
50-100 hp
Gearbox Horsepower
splitter 160 hp, center & wings 75 hp
Gearbox shafts
input shaft 1 3/8" 6 Spline, output shaft 1 5/8"
Gear Box Lubrication
splitter 4.5 Pints of gear lube, center & wings 5.75 Lints of gear lube
Gearbox Capacity
splitter and center & wings - 80-90W EP
Cutting Capacity
1 1/2"
Hitch weight
1,022 lbs.
Machine Weight
3,202 lbs. with chain guards & four laminated tires.
Blade Tip Speed at 540 rpm
Center blades & wing blades = 14,963 FPM
Hitch Types
Pull-type hitch & clevis
Hitch Jack
Standard (2,000 lbs.)
Cutting Width
15' - 0"
Overall Width
15' - 7"
Normal transport width
10' - 2 1/2" With transport locks set and cutting blade 13" off the ground.
Minimum Transport Width
8' - 4" With transport locks set and cutting blade 2" off the ground.
Overall Length
15' - 2" With laminated tires, 15' - 5 1/2" With aircraft tires
Deck Height
11 1/4"
Cutting Height
2" to 13"
Lift Hydraulics
2 1/2" x 8" hydraulic cylinder, hoses, fittings & stroke control spacers
Wing Hydraulics
2 1/2" x 10" hydraulic cylinders, hoses & fittings
Wing Transport Protection
Wing transport locks
Deck Material
10 Gauge deck
Side Skirt Material
1/4" Plate
Skid Shoes
Wing Deck: 1 replaceable shoe per wing. Center Deck: 2 replaceable shoes
Blade rotation
Left wing - clockwise, center deck and right wing - counterclockwise
Blades - 6 (2 per deck)
1/2" x 4" Heat treated free swinging alloy steel with up lift
Blade Overlap
Blade Bolt
Keyed with hardened flat washer & lock nut
Stump Jumper / Blade Holder
10 Gauge round dish shaped pan, reinforced with 1" x 4" blade bar
Front & Rear Guards
Single chain or rubber
Input Driveline
ASAE Category 4 with constant velocity u-joint
Intermediate & wing drivelines
ASAE Category 3 with slip-clutch
29" Used aircraft tires or 21" laminated wheels
Number of Wheels
4 or 6 Total
Transport Axle
Spring-cushioned lift cylinder
Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" shafts.
Standard color: Beige; Optional colors: Green, Orange, or Red
Hendrix Machinery, Inc. is a dealer of Kubota, Woods, Bush Hog, Princeton Delivery Systems, Alamo Industrial, Brown Manufacturing and Land Pride.