Hendrix Machinery, Inc.
(912) 964-7790
1725 Old Dean Forest Road
Pooler, GA 31322


2018 LAND PRIDE RC3615

2018 LAND PRIDE RC3615 at www.hendrixmachinery.com2018 LAND PRIDE RC3615 at www.hendrixmachinery.com
2018 LAND PRIDE RC3615 at www.hendrixmachinery.com2018 LAND PRIDE RC3615 at www.hendrixmachinery.com
2018 LAND PRIDE RC3615 at www.hendrixmachinery.com2018 LAND PRIDE RC3615 at www.hendrixmachinery.com
2018 LAND PRIDE RC3615 at www.hendrixmachinery.com2018 LAND PRIDE RC3615 at www.hendrixmachinery.com

For Sale Price:Call


Land Pride's RC3615 and RCM3615 Series Rotary Cutters are ideal for maintaining grazing areas for horses or mowing the wide open spaces close to town. The 15' cutting width and ability to cut weeds and brush up to 2.5" in diameter make them well suited for these applications. The 36 Series offers a pull-type self leveling tongue with a clevis hitch for attachment to 50-160 hp tractors. Safety guards around the cutter are offered in either chain or rubber.

Surpassed rugged industry standards
All Land Pride Rotary Cutters have been designed and tested and meet rigorous voluntary testing procedures according to ISO 4254-13.

Factory assembled
Arrives for quick and easy set-up. Minimal time is wasted setting or prepping the unit.

5 Year gearbox warranty
Shows confidence in gearbox integrity.

Rugged heavy built gearboxes
Capable of handling heavy cutting applications.

Gearbox seal protection
Gearbox bottom seal protection for longer bearing life.

2 Piece shield on wing gearboxes
Driveline grease zerks are easier to access.

LP Performance self-leveling hitch
Reduces drawbar wear by keeping hitch level while going through ditches.

Low hitch weight on tractor tongue
Ideal for smaller HP tractors by reducing the amount of weight on the drawbar.

Narrow A-frame hitch Allows for a tighter turning radius.
Adjustable park jack angle Park jack can be adjusted to be perpendicular to the ground.

Adjustable driveline hanger
Serves as a support rest for the driveline when the cutter is unhooked from the tractor. Assist operator when attaching driveline to tractor PTO shaft.

Input driveline: Cat. 6 CV or Cat. 5 Conventional
Driveline is matched just right for capacity of tractor. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline.

Drivelines with slip-clutches: Cat. 5 intermediate, Cat. 4 Wings
Driveline is sized right for the intended cutting capacity. Slip-clutches will slip under load to minimize twist damage to driveline profiles.

Grease zerks on end caps of driveline cross journals
Intermediate and wing driveline cross journals are easier to grease.

High blade tip speed
Allows clean cutting of material.

6" Blade overlap
Eliminates skipping during turns.

3/16" Round stump jumper
Standard thick stump jumper material keeps damage to a minimum.

Smooth top design
Reduces accumulation of debris and is easier and faster to clean.

Deck sheet tops are 100% welded .
Makes center decks and wing decks stronger.

Left wing rotates clockwise
Better discharge of material. Picks up tractor tracks.

1/4" Sidewall thickness
Increased thickness reduces damage from objects being thrown into deck sidewalls.

Beveled skid shoes on wings
Reduces gouging the ground when turning.

Hinged wing sections
Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting.

1" Solid hinge rods
Larger diameter hinge rod gives greater strength to the cutter from front to rear, and in the hinge area itself.

Wing transport locks
Wing transport locks will hold wings in the folded position in the event of hydraulic loss.

Enclosed dual leveling rods
Cutter pulls equally on the rear axle while traveling over rough terrain.

5-Bolt hubs
5-Bolt hubs makes the wheel assembly more durable and longer lasting.

Drain holes in wheel rims
Allows water to drain from wheels mounted on folded-up wings. Helps prevent paint deterioration and rusting to the wheel rims.

Spring cushioned center-axle
Protects unit from bumps and ground shock.

Replaceable wheel spindles
Wheel spindles can be replaced when damaged without replacing entire axle assembly.

Wheel options
Laminated tires: Eliminates flats.
Air-filled tires: Give better cushion while transporting.
Foam-filled tires: Give better cushion while transporting and can’t go flat.

LP Performance hitch option
Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and pivots about the tractor drawbar.

Bar-tite hitch option
Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.

Roadway light kit option
Allows operator to transport on public roads safer.


Horsepower Range
50 - 160
Gearbox Horsepower
540 rpm or 1000 rpm, 160 hp Divider, 130 hp Center & Wings
Gear Box Lubrication
Gear Lube 80-90W EP
Gearbox Oil Capacity
Splitter: 3.5 pints; Center deck & Wings: 6 pints
Cutting Capacity
2 1/2"
Machine Weight
Total weight - 3,730 lbs. Tongue weight - 1,240 lbs.
Blade Tip Speed
At 540 rpm - Center blades = 15,268 FPM & Wing blades = 15,000 FPM At 1000 rpm - Center blades = 15,578 FPM & Wing blades = 14,620 FPM
Hitch Types
Standard Clevis, LP Performance Hitch, Bar-Tite Hitch, Ball Hitch, or Pintle Hitch
Hitch Jack
Standard (7,000 lbs.)
Signal lights
7 Pin connector
SAE J560 pin configuration
Cutting Width
Overall Width
15'-11 1/2"
Minimum Transport Width
7'-11 3/4"
Overall Length
15'-6" (With center deck raised fully up)
Deck Height
Cutting Height
2" - 14"
Lift Hydraulics
3" x 8" hydraulic cylinder, hoses, fittings & stroke control spacers
Wing Hydraulics
2 1/2" x 12" hydraulic cylinders, hoses & fittings
Wing Transport Protection
Wing Transport Locks
Deck Material Thickness
10 Gauge
Side Skirt Thickness
1/4" Steel
Skid Shoes
Wing Deck: AR400 1 replaceable skid shoe per wing. Center Deck: AR400 2 replaceable skid shoes
Blades - 6 (2 per Carrier)
1/2" x 4" Heat treated, Free swinging alloy steel with uplift
Blade Overlap
Blade Bolt
Keyed with hardened flat washer & locknut
Stump Jumper / Blade Holder
3/16" Thick round dish shaped pan, reinforced with 1" x 4" blade bar
Front & Rear Guards
Optional rubber, single row chain or dual row chain
Input Driveline 540 & 1000 rpm
Cat. 6 with constant velocity u-joint or Cat. 5 with conventional (non-cv) u-joint
Intermediate Driveline
Standard - Category 5 with slip-clutch
Wing Drivelines
Standard - Category 4 with slip-clutch
Wheel Options
6" x 21" Laminated tires, 25.5" new foam filled tires, 29" x 16 ply used aircraft tires without foam filling.
Number of Wheels
4 - Wheels: Two on transport axle and one on each wing axle. 6 - Wheel option: Four on transport axle and one on each wing axle. 8 - Wheel option: Four on transport axle and two on each wing axle.
Transport Axle
Spring-cushioned on center transport axle
Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" shafts.
Deck Rings
Hendrix Machinery, Inc. is a dealer of Kubota, Woods, Bush Hog, Princeton Delivery Systems, Alamo Industrial, Brown Manufacturing and Land Pride.